Hard disk drive
------------------------------------------
SHORTCUT
A Brief History of the Hard Disk Drive
The hard disk drive has short and fascinating history. In 24 years it evolved from a monstrosity with fifty two-foot diameter disks holding five MBytes (5,000,000 bytes) of data to today's drives measuring 3 /12 inches wide and an inch high (and smaller) holding 400 GBytes (400,000,000,000 bytes/characters). Here, then, is the short history of this marvelous device.
Before the disk drive there were drums... In 1950 Engineering Research Associates of Minneapolis built the first commercial magnetic drum storage unit for the U.S. Navy, the ERA 110. It could store one million bits of data and retrieve a word in 5 thousandths of a second.
In 1956 IBM invented the first computer disk storage system, the 305 RAMAC (Random Access Method of Accounting and Control). This system could store five MBytes. It had fifty, 24-inch diameter disks!
By 1961 IBM had invented the first disk drive with air bearing heads and in 1963 they introduced the removable disk pack drive.
In 1970 the eight inch floppy disk drive was introduced by IBM. My first floppy drives were made by Shugart who was one of the "dirty dozen" who left IBM to start their own companies. In 1981 two Shugart 8 inch floppy drives with enclosure and power supply cost me about $350.00. They were for my second computer. My first computer had no drives at all.
In 1973 IBM shipped the model 3340 Winchester sealed hard disk drive, the predecessor of all current hard disk drives. The 3340 had two spindles each with a capacity of 30 MBytes, and the term "30/30 Winchester" was thus coined.
In 1980, Seagate Technology introduced the first hard disk drive for microcomputers, the ST506. It was a full height (twice as high as most current 5 1/4" drives) 5 1/4" drive, with a stepper motor, and held 5 Mbytes. My first hard disk drive was an ST506. I cannot remember exactly how much it cost, but it plus its enclosure, etc. was well over a thousand dollars. It took me three years to fill the drive. Also, in 1980 Phillips introduced the first optical laser drive. In the early 80's, the first 5 1/4" hard disks with voice coil actuators (more on this later) started shipping in volume, but stepper motor drives continued in production into the early 1990's. In 1981, Sony shipped the first 3 1/2" floppy drives.
In 1983 Rodime made the first 3.5 inch rigid disk drive. The first CD-ROM drives were shipped in 1984, and "Grolier's Electronic Encyclopedia," followed in 1985. The 3 1/2" IDE drive started its existence as a drive on a plug-in expansion board, or "hard card." The hard card included the drive on the controller which, in turn, evolved into Integrated Device Electronics (IDE) hard disk drive, where the controller became incorporated into the printed circuit on the bottom of the hard disk drive. Quantum made the first hard card in 1985.
In 1986 the first 3 /12" hard disks with voice coil actuators were introduced by Conner in volume, but half (1.6") and full height 5 1/4" drives persisted for several years. In 1988 Conner introduced the first one inch high 3 1/2" hard disk drives. In the same year PrairieTek shipped the first 2 1/2" hard disks.
In 1997 Seagate introduced the first 7,200 RPM, Ultra ATA hard disk drive for desktop computers and in February of this year they introduced the first 15,000 RPM hard disk drive, the Cheetah X15. Milestones for IDE DMA, ATA/33, and ATA/66 drives follow:
* 1994 DMA, Mode 2 at 16.6 MB/s
* 1997 Ultra ATA/33 at 33.3 MB/s
* 1999 Ultra ATA/66 at 66.6 MB/s
6/20/00 IBM triples the capacity of the world's smallest hard disk drive. This drive holds one gigabyte on a disk which is the size of an American quarter. The world's first gigabyte-capacity disk drive, the IBM 3380, introduced in 1980, was the size of a refrigerator, weighed 550 pounds (about 250 kg), and had a price tag of $40,000.
FULL INFO
----------------------------------
A hard disk drive (HDD) is a non-volatile, random access device for digital data. It features rotating rigid platters on a motor-driven spindle within a protective enclosure. Data is magnetically read from and written to the platter by read/write heads that float on a film of air above the platters.
Introduced by IBM in 1956, hard disk drives have fallen in cost and physical size over the years while dramatically increasing in capacity. Hard disk drives have been the dominant device for secondary storage of data in general purpose computers since the early 1960s. They have maintained this position because advances in their areal recording density have kept pace with the requirements for secondary storage.[Today's HDDs operate on high-speed serial interfaces; i.e., serial ATA (SATA) or serial attached SCSI (SAS).
HISTORY
Hard disk drives were introduced in 1956 as data storage for an IBM accounting computer and were developed for use with general purpose mainframe and mini computers.
Driven by areal density doubling every two to four years since their invention, HDDs have changed in many ways, a few highlights include:
* Capacity per HDD increasing from 3.75 megabytes to greater than 1 terabyte, a greater than 270 thousand to 1 improvement.
* Size of HDD decreasing from 87.9 cubic feet (a double wide refrigerator) to 0.002 cubic feet (2½-inch form factor, a pack of cards), a greater than 44 thousand to 1 improvement.
* Price decreasing from about $15,000 per megabyte to less than $0.0001 per megabyte ($100/1 terabyte), a greater than 150 million to 1 improvement.
* Average access time decreasing from greater than 0.1 second to a few thousandths of a second, a greater than 40 to 1 improvement.
* Market application expanding from general purpose computers to most computing applications including consumer applications.
Technology
-------------------------------------------------------
Magnetic recording
HDDs record data by magnetizing ferromagnetic material directionally. Sequential changes in the direction of magnetization represent patterns of binary data bits. The data are read from the disk by detecting the transitions in magnetization and decoding the originally written data. Different encoding schemes, such as Modified Frequency Modulation, group code recording, run-length limited encoding, and others are used.
A typical HDD design consists of a spindle that holds flat circular disks called platters, onto which the data are recorded. The platters are made from a non-magnetic material, usually aluminum alloy or glass, and are coated with a shallow layer of magnetic material typically 10–20 nm in depth, with an outer layer of carbon for protection. For reference, standard copy paper is 0.07–0.18 millimetre (70,000–180,000 nm).
The platters are spun at speeds varying from 3,000 RPM in energy-efficient portable devices, to 15,000 RPM for high performance servers. Information is written to, and read from a platter as it rotates past devices called read-and-write heads that operate very close (tens of nanometers in new drives) over the magnetic surface. The read-and-write head is used to detect and modify the magnetization of the material immediately under it. In modern drives there is one head for each magnetic platter surface on the spindle, mounted on a common arm. An actuator arm (or access arm) moves the heads on an arc (roughly radially) across the platters as they spin, allowing each head to access almost the entire surface of the platter as it spins. The arm is moved using a voice coil actuator or in some older designs a stepper motor.
The magnetic surface of each platter is conceptually divided into many small sub-micrometer-sized magnetic regions referred to as magnetic domains. In older disk designs the regions were oriented horizontally and parallel to the disk surface, but beginning about 2005, the orientation was changed to perpendicular to allow for closer magnetic domain spacing. Due to the polycrystalline nature of the magnetic material each of these magnetic regions is composed of a few hundred magnetic grains. Magnetic grains are typically 10 nm in size and each form a single magnetic domain. Each magnetic region in total forms a magnetic dipole which generates a magnetic field.
For reliable storage of data, the recording material needs to resist self-demagnetization, which occurs when the magnetic domains repel each other. Magnetic domains written too densely together to a weakly magnetizable material will degrade over time due to physical rotation of one or more domains to cancel out these forces. The domains rotate sideways to a halfway position that weakens the readability of the domain and relieves the magnetic stresses. Older hard disks used iron(III) oxide as the magnetic material, but current disks use a cobalt-based alloy.
A write head magnetizes a region by generating a strong local magnetic field. Early HDDs used an electromagnet both to magnetize the region and to then read its magnetic field by using electromagnetic induction. Later versions of inductive heads included metal in Gap (MIG) heads and thin film heads. As data density increased, read heads using magnetoresistance (MR) came into use; the electrical resistance of the head changed according to the strength of the magnetism from the platter. Later development made use of spintronics; in these heads, the magnetoresistive effect was much greater than in earlier types, and was dubbed "giant" magnetoresistance (GMR). In today's heads, the read and write elements are separate, but in close proximity, on the head portion of an actuator arm. The read element is typically magneto-resistive while the write element is typically thin-film inductive.
The heads are kept from contacting the platter surface by the air that is extremely close to the platter; that air moves at or near the platter speed. The record and playback head are mounted on a block called a slider, and the surface next to the platter is shaped to keep it just barely out of contact. This forms a type of air bearing.
In modern drives, the small size of the magnetic regions creates the danger that their magnetic state might be lost because of thermal effects. To counter this, the platters are coated with two parallel magnetic layers, separated by a 3-atom layer of the non-magnetic element ruthenium, and the two layers are magnetized in opposite orientation, thus reinforcing each other. Another technology used to overcome thermal effects to allow greater recording densities is perpendicular recording, first shipped in 2005, and as of 2007 the technology was used in many HDDs.
Components
A typical hard disk drive has two electric motors; a disk motor to spin the disks and an actuator (motor) to position the read/write head assembly across the spinning disks.
The disk motor has an external rotor attached to the disks; the stator windings are fixed in place.
Opposite the actuator at the end of the head support arm is the read-write head (near center in photo); thin printed-circuit cables connect the read-write heads to amplifier electronics mounted at the pivot of the actuator. A flexible, somewhat U-shaped, ribbon cable, seen edge-on below and to the left of the actuator arm continues the connection to the controller board on the opposite side.
The head support arm is very light, but also stiff; in modern drives, acceleration at the head reaches 550 Gs.
The silver-colored structure at the upper left of the first image is the top plate of the actuator, a permanent-magnet and moving coil motor that swings the heads to the desired position (it is shown removed in the second image). The plate supports a squat neodymium-iron-boron (NIB) high-flux magnet. Beneath this plate is the moving coil, often referred to as the voice coil by analogy to the coil in loudspeakers, which is attached to the actuator hub, and beneath that is a second NIB magnet, mounted on the bottom plate of the motor (some drives only have one magnet).
The voice coil itself is shaped rather like an arrowhead, and made of doubly coated copper magnet wire. The inner layer is insulation, and the outer is thermoplastic, which bonds the coil together after it is wound on a form, making it self-supporting. The portions of the coil along the two sides of the arrowhead (which point to the actuator bearing center) interact with the magnetic field, developing a tangential force that rotates the actuator. Current flowing radially outward along one side of the arrowhead and radially inward on the other produces the tangential force. If the magnetic field were uniform, each side would generate opposing forces that would cancel each other out. Therefore the surface of the magnet is half N pole, half S pole, with the radial dividing line in the middle, causing the two sides of the coil to see opposite magnetic fields and produce forces that add instead of canceling. Currents along the top and bottom of the coil produce radial forces that do not rotate the head.
CAPACITY
Hard disk manufacturers quote disk capacity in multiples of SI-standard powers of 1000, where a terabyte is 1000 gigabytes and a gigabyte is 1000 megabytes. With file systems that report capacity in powers of 1024, available space appears somewhat less than advertised capacity. The discrepancy between the two methods of reporting sizes had serious financial consequences for at least one hard drive manufacturer when a class action suit argued the different methods effectively misled consumers.
Semiconductor memory chips are organized so that memory sizes are expressed in multiples of powers of two. Hard disks by contrast have no inherent binary size. Capacity is the product of the number of heads, number of tracks, number of sectors per track, and the size of each sector. Sector sizes are standardized for convenience at 256 or 512 and more recently 4096 bytes, which are powers of two. This can cause some confusion because operating systems may report the formatted capacity of a hard drive using binary prefix units which increment by powers of 1024. For example, Microsoft Windows reports disk capacity both in a decimal integer to 12 or more digits and in binary prefix units to three significant digits.
A one terabyte (1 TB) disk drive would be expected to hold around 1 trillion bytes (1,000,000,000,000) or 1000 GB; and indeed most 1 TB hard drives will contain slightly more than this number. However some operating system utilities would report this as around 931 GB or 953,674 MB. (The actual number for a formatted capacity will be somewhat smaller still, depending on the file system.) Following are the several ways of reporting one Terabyte.
SALES
Worldwide revenue from shipments of HDDs is expected to reach $27.7 billion in 2010, up 18.4% from $23.4 billion in 2009[77] corresponding to a 2010 unit shipment forecast of 674.6 million compared to 549.5 million units in 2009.
BY: HARMANJEET SINGH , IX , GMA ,SITE MANAGER
MORE INFO OPTIONS:
WIKIPEDIA
GOOGLE SEARCH
------------------------------------------
 |
| A Western Digital 3.5 inch 250 GB SATA HDD; this specific model features both SATA and Molex power inputs |
SHORTCUT
A Brief History of the Hard Disk Drive
The hard disk drive has short and fascinating history. In 24 years it evolved from a monstrosity with fifty two-foot diameter disks holding five MBytes (5,000,000 bytes) of data to today's drives measuring 3 /12 inches wide and an inch high (and smaller) holding 400 GBytes (400,000,000,000 bytes/characters). Here, then, is the short history of this marvelous device.
Before the disk drive there were drums... In 1950 Engineering Research Associates of Minneapolis built the first commercial magnetic drum storage unit for the U.S. Navy, the ERA 110. It could store one million bits of data and retrieve a word in 5 thousandths of a second.
In 1956 IBM invented the first computer disk storage system, the 305 RAMAC (Random Access Method of Accounting and Control). This system could store five MBytes. It had fifty, 24-inch diameter disks!
By 1961 IBM had invented the first disk drive with air bearing heads and in 1963 they introduced the removable disk pack drive.
In 1970 the eight inch floppy disk drive was introduced by IBM. My first floppy drives were made by Shugart who was one of the "dirty dozen" who left IBM to start their own companies. In 1981 two Shugart 8 inch floppy drives with enclosure and power supply cost me about $350.00. They were for my second computer. My first computer had no drives at all.
In 1973 IBM shipped the model 3340 Winchester sealed hard disk drive, the predecessor of all current hard disk drives. The 3340 had two spindles each with a capacity of 30 MBytes, and the term "30/30 Winchester" was thus coined.
In 1980, Seagate Technology introduced the first hard disk drive for microcomputers, the ST506. It was a full height (twice as high as most current 5 1/4" drives) 5 1/4" drive, with a stepper motor, and held 5 Mbytes. My first hard disk drive was an ST506. I cannot remember exactly how much it cost, but it plus its enclosure, etc. was well over a thousand dollars. It took me three years to fill the drive. Also, in 1980 Phillips introduced the first optical laser drive. In the early 80's, the first 5 1/4" hard disks with voice coil actuators (more on this later) started shipping in volume, but stepper motor drives continued in production into the early 1990's. In 1981, Sony shipped the first 3 1/2" floppy drives.
In 1983 Rodime made the first 3.5 inch rigid disk drive. The first CD-ROM drives were shipped in 1984, and "Grolier's Electronic Encyclopedia," followed in 1985. The 3 1/2" IDE drive started its existence as a drive on a plug-in expansion board, or "hard card." The hard card included the drive on the controller which, in turn, evolved into Integrated Device Electronics (IDE) hard disk drive, where the controller became incorporated into the printed circuit on the bottom of the hard disk drive. Quantum made the first hard card in 1985.
In 1986 the first 3 /12" hard disks with voice coil actuators were introduced by Conner in volume, but half (1.6") and full height 5 1/4" drives persisted for several years. In 1988 Conner introduced the first one inch high 3 1/2" hard disk drives. In the same year PrairieTek shipped the first 2 1/2" hard disks.
In 1997 Seagate introduced the first 7,200 RPM, Ultra ATA hard disk drive for desktop computers and in February of this year they introduced the first 15,000 RPM hard disk drive, the Cheetah X15. Milestones for IDE DMA, ATA/33, and ATA/66 drives follow:
* 1994 DMA, Mode 2 at 16.6 MB/s
* 1997 Ultra ATA/33 at 33.3 MB/s
* 1999 Ultra ATA/66 at 66.6 MB/s
6/20/00 IBM triples the capacity of the world's smallest hard disk drive. This drive holds one gigabyte on a disk which is the size of an American quarter. The world's first gigabyte-capacity disk drive, the IBM 3380, introduced in 1980, was the size of a refrigerator, weighed 550 pounds (about 250 kg), and had a price tag of $40,000.
FULL INFO
----------------------------------
A hard disk drive (HDD) is a non-volatile, random access device for digital data. It features rotating rigid platters on a motor-driven spindle within a protective enclosure. Data is magnetically read from and written to the platter by read/write heads that float on a film of air above the platters.
Introduced by IBM in 1956, hard disk drives have fallen in cost and physical size over the years while dramatically increasing in capacity. Hard disk drives have been the dominant device for secondary storage of data in general purpose computers since the early 1960s. They have maintained this position because advances in their areal recording density have kept pace with the requirements for secondary storage.[Today's HDDs operate on high-speed serial interfaces; i.e., serial ATA (SATA) or serial attached SCSI (SAS).
HISTORY
Hard disk drives were introduced in 1956 as data storage for an IBM accounting computer and were developed for use with general purpose mainframe and mini computers.
Driven by areal density doubling every two to four years since their invention, HDDs have changed in many ways, a few highlights include:
* Capacity per HDD increasing from 3.75 megabytes to greater than 1 terabyte, a greater than 270 thousand to 1 improvement.
* Size of HDD decreasing from 87.9 cubic feet (a double wide refrigerator) to 0.002 cubic feet (2½-inch form factor, a pack of cards), a greater than 44 thousand to 1 improvement.
* Price decreasing from about $15,000 per megabyte to less than $0.0001 per megabyte ($100/1 terabyte), a greater than 150 million to 1 improvement.
* Average access time decreasing from greater than 0.1 second to a few thousandths of a second, a greater than 40 to 1 improvement.
* Market application expanding from general purpose computers to most computing applications including consumer applications.
Technology
-------------------------------------------------------
Magnetic recording
HDDs record data by magnetizing ferromagnetic material directionally. Sequential changes in the direction of magnetization represent patterns of binary data bits. The data are read from the disk by detecting the transitions in magnetization and decoding the originally written data. Different encoding schemes, such as Modified Frequency Modulation, group code recording, run-length limited encoding, and others are used.
A typical HDD design consists of a spindle that holds flat circular disks called platters, onto which the data are recorded. The platters are made from a non-magnetic material, usually aluminum alloy or glass, and are coated with a shallow layer of magnetic material typically 10–20 nm in depth, with an outer layer of carbon for protection. For reference, standard copy paper is 0.07–0.18 millimetre (70,000–180,000 nm).
The platters are spun at speeds varying from 3,000 RPM in energy-efficient portable devices, to 15,000 RPM for high performance servers. Information is written to, and read from a platter as it rotates past devices called read-and-write heads that operate very close (tens of nanometers in new drives) over the magnetic surface. The read-and-write head is used to detect and modify the magnetization of the material immediately under it. In modern drives there is one head for each magnetic platter surface on the spindle, mounted on a common arm. An actuator arm (or access arm) moves the heads on an arc (roughly radially) across the platters as they spin, allowing each head to access almost the entire surface of the platter as it spins. The arm is moved using a voice coil actuator or in some older designs a stepper motor.
The magnetic surface of each platter is conceptually divided into many small sub-micrometer-sized magnetic regions referred to as magnetic domains. In older disk designs the regions were oriented horizontally and parallel to the disk surface, but beginning about 2005, the orientation was changed to perpendicular to allow for closer magnetic domain spacing. Due to the polycrystalline nature of the magnetic material each of these magnetic regions is composed of a few hundred magnetic grains. Magnetic grains are typically 10 nm in size and each form a single magnetic domain. Each magnetic region in total forms a magnetic dipole which generates a magnetic field.
For reliable storage of data, the recording material needs to resist self-demagnetization, which occurs when the magnetic domains repel each other. Magnetic domains written too densely together to a weakly magnetizable material will degrade over time due to physical rotation of one or more domains to cancel out these forces. The domains rotate sideways to a halfway position that weakens the readability of the domain and relieves the magnetic stresses. Older hard disks used iron(III) oxide as the magnetic material, but current disks use a cobalt-based alloy.
A write head magnetizes a region by generating a strong local magnetic field. Early HDDs used an electromagnet both to magnetize the region and to then read its magnetic field by using electromagnetic induction. Later versions of inductive heads included metal in Gap (MIG) heads and thin film heads. As data density increased, read heads using magnetoresistance (MR) came into use; the electrical resistance of the head changed according to the strength of the magnetism from the platter. Later development made use of spintronics; in these heads, the magnetoresistive effect was much greater than in earlier types, and was dubbed "giant" magnetoresistance (GMR). In today's heads, the read and write elements are separate, but in close proximity, on the head portion of an actuator arm. The read element is typically magneto-resistive while the write element is typically thin-film inductive.
The heads are kept from contacting the platter surface by the air that is extremely close to the platter; that air moves at or near the platter speed. The record and playback head are mounted on a block called a slider, and the surface next to the platter is shaped to keep it just barely out of contact. This forms a type of air bearing.
In modern drives, the small size of the magnetic regions creates the danger that their magnetic state might be lost because of thermal effects. To counter this, the platters are coated with two parallel magnetic layers, separated by a 3-atom layer of the non-magnetic element ruthenium, and the two layers are magnetized in opposite orientation, thus reinforcing each other. Another technology used to overcome thermal effects to allow greater recording densities is perpendicular recording, first shipped in 2005, and as of 2007 the technology was used in many HDDs.
Components
 |
| A hard disk drive with the disks and motor hub removed showing the copper colored stator coils surrounding a bearing at the center of the spindle motor. The orange stripe along the side of the arm is a thin printed-circuit cable. The spindle bearing is in the center. The actuator is in the upper left. |
A typical hard disk drive has two electric motors; a disk motor to spin the disks and an actuator (motor) to position the read/write head assembly across the spinning disks.
The disk motor has an external rotor attached to the disks; the stator windings are fixed in place.
Opposite the actuator at the end of the head support arm is the read-write head (near center in photo); thin printed-circuit cables connect the read-write heads to amplifier electronics mounted at the pivot of the actuator. A flexible, somewhat U-shaped, ribbon cable, seen edge-on below and to the left of the actuator arm continues the connection to the controller board on the opposite side.
The head support arm is very light, but also stiff; in modern drives, acceleration at the head reaches 550 Gs.
The silver-colored structure at the upper left of the first image is the top plate of the actuator, a permanent-magnet and moving coil motor that swings the heads to the desired position (it is shown removed in the second image). The plate supports a squat neodymium-iron-boron (NIB) high-flux magnet. Beneath this plate is the moving coil, often referred to as the voice coil by analogy to the coil in loudspeakers, which is attached to the actuator hub, and beneath that is a second NIB magnet, mounted on the bottom plate of the motor (some drives only have one magnet).
The voice coil itself is shaped rather like an arrowhead, and made of doubly coated copper magnet wire. The inner layer is insulation, and the outer is thermoplastic, which bonds the coil together after it is wound on a form, making it self-supporting. The portions of the coil along the two sides of the arrowhead (which point to the actuator bearing center) interact with the magnetic field, developing a tangential force that rotates the actuator. Current flowing radially outward along one side of the arrowhead and radially inward on the other produces the tangential force. If the magnetic field were uniform, each side would generate opposing forces that would cancel each other out. Therefore the surface of the magnet is half N pole, half S pole, with the radial dividing line in the middle, causing the two sides of the coil to see opposite magnetic fields and produce forces that add instead of canceling. Currents along the top and bottom of the coil produce radial forces that do not rotate the head.
CAPACITY
Hard disk manufacturers quote disk capacity in multiples of SI-standard powers of 1000, where a terabyte is 1000 gigabytes and a gigabyte is 1000 megabytes. With file systems that report capacity in powers of 1024, available space appears somewhat less than advertised capacity. The discrepancy between the two methods of reporting sizes had serious financial consequences for at least one hard drive manufacturer when a class action suit argued the different methods effectively misled consumers.
Semiconductor memory chips are organized so that memory sizes are expressed in multiples of powers of two. Hard disks by contrast have no inherent binary size. Capacity is the product of the number of heads, number of tracks, number of sectors per track, and the size of each sector. Sector sizes are standardized for convenience at 256 or 512 and more recently 4096 bytes, which are powers of two. This can cause some confusion because operating systems may report the formatted capacity of a hard drive using binary prefix units which increment by powers of 1024. For example, Microsoft Windows reports disk capacity both in a decimal integer to 12 or more digits and in binary prefix units to three significant digits.
A one terabyte (1 TB) disk drive would be expected to hold around 1 trillion bytes (1,000,000,000,000) or 1000 GB; and indeed most 1 TB hard drives will contain slightly more than this number. However some operating system utilities would report this as around 931 GB or 953,674 MB. (The actual number for a formatted capacity will be somewhat smaller still, depending on the file system.) Following are the several ways of reporting one Terabyte.
SALES
Worldwide revenue from shipments of HDDs is expected to reach $27.7 billion in 2010, up 18.4% from $23.4 billion in 2009[77] corresponding to a 2010 unit shipment forecast of 674.6 million compared to 549.5 million units in 2009.
BY: HARMANJEET SINGH , IX , GMA ,SITE MANAGER
MORE INFO OPTIONS:
WIKIPEDIA
GOOGLE SEARCH
